Room sensor offline Issue Troubleshooting Guide

Room sensor offline Issue Troubleshooting Guide

MONAIRE Knowledge Base
For Facility Teams & Technicians

What does the "Room sensor offline" issue mean?

  • Cause: A wireless room sensor linked to your Monaire thermostat has lost Radio Frequency communication to the Monaire Gateway or depleted its battery power (you will be able to confirm this through the Monaire Web/Mobile app charts).
  • Space Temperature Reading: The system is currently unable to read the space temperature from that remote location.
  • Equipment Fallback:Heating and cooling continue functioning normally; the thermostat automatically defaults to reading room temperature from the Monaire thermostat (temperature of the space might not be properly monitored if the thermostat was not installed  in the actual space it is serving).
💡 Multi-zone temperature sensing is temporarily paused while the wireless room sensor is offline. Indoor temperature is now measured at the physical thermostat. This has no impact on your HVAC equipment's ability to call for heating or cooling.

Hardware Troubleshooting Steps

Execute these steps in order before approving a technician dispatch:

1

 Reset the Sensor

Locate the offline room sensor in your space. Press and hold the Connect button on the sensor until an amber light flashes (about 10 to 30 seconds).

💡 Note: You will have to remove the front cover of the sensor to access the Connect button.
Room Sensor Reset Button and Cover
• If the amber light flashes: The sensor has been reset. Proceed to Step 2 to re-pair it.
• If no light flashes after holding for 30s: The sensor batteries are depleted. Skip to Step 3 to replace the batteries.
2

 Pair Sensor to Thermostat

Bring the room sensor within 5 feet of the physical thermostat display.

📍 Important — Confirm Correct Thermostat: Ensure you pair the sensor to the thermostat controlling that space. For example, if the offline room sensor was located in the Dining Room, make sure you locate and pair it to the thermostat labeled Dining Room under Devices & Sensors.
On the physical thermostat touchscreen:
  1. Tap the three stacked lines (hamburger menu icon) and scroll down.
  2. Go to Devices & Sensors.
  3. Tap Add and follow the on-screen pairing instructions.
  4. Tap the Indoor Room sensor > Change Room > Other > +Add Room
    1. This step is crucial to ensure the thermostat is monitoring room temperature data from the correct space that needs to be conditioned.
Pair Sensor to Thermostat
Add Room Steps
🔍 Thermostat & Room Sensor Series Compatibility Check:

Not all wireless room sensors can connect to all thermostat models. If the sensor fails to pair during Step 2, locate the series number of each hardware:

  • Wireless Room Sensor: Remove the batteries from the room sensor to view the series number printed inside the battery compartment. See photo below.
  • Thermostat: Pop the thermostat off the wall mounting bracket to view the series number printed on the back label. See photo below.
Review compatibility: The series number of the thermostat must be equal to or less than the series number on the wireless room sensor (I.e. a series 2 thermostat will not connect to series 1 wireless room sensor).
Wireless room sensor
Wireless room sensor
Backplate of the Monaire Thermostat T10+ Model
Backplate of Monaire Thermostat (Elite Pro Model)
Backplate of Monaire Thermostat (Elite Pro Model)
3

 Replace Sensor Batteries & Retry Pairing

If pairing fails or no light appeared during the reset in Step 1, replace the sensor's batteries:

  • Replace Batteries: Carefully remove the front cover of the room sensor and insert fresh AAA batteries.
  • Retry Pairing: Once fresh batteries are installed, repeat Step 2 to pair the sensor to the thermostat touchscreen.
4

 Confirm Settings: Priority, Motion Sensing, and Monaire Connection

After re-pairing, confirm settings are properly configured in the Monaire App and on the thermostat:

Set Priority (Monaire App: mobile or web)
Use the Monaire App to configure which hardware should be in priority to correctly read the indoor temperature (or, if the temperatures at the wireless room sensor and thermostat should be averaged).
How to configure priority in the Monaire App
  1. View Details: Navigate to the main Equipment details screen.
  2. Select Equipment Type: Tap on the relevant equipment category (e.g., RTU(S) or AC).
  3. Choose Specific Equipment: Tap the arrow to the right of the specific unit you want to adjust (e.g., RTU 1).
  4. Go to Thermostat Settings: On the unit's page, scroll the top menu to the right and tap the Thermostat tab.
  5. View Thermostat Details: Scroll down to the bottom of the thermostat page and tap View details.
  6. Change Priority: Scroll down to the "In priority" section and tap the Change button (pencil icon).
  7. Select Hardware: Choose the correct sensor (hardware) or room you wish to prioritize.
  8. Save Changes: Tap Done to confirm your selection, then select Yes to save.
Note: Setting sensor priority at the physical thermostat display does not make the change permanent and only holds until the next scheduled period.
Turn OFF Motion Sensing (Monaire Thermostat)
Devices & Sensors > Indoor Air Sensor > Options... > Toggle 'Use Motion' OFF
Toggle OFF to disable motion sensing as this greatly extends the battery life.
Confirm Sensor Connection (Monaire Thermostat, then Monaire App)
Devices & Sensors > Indoor Air Sensor > Options... > Blink Lights > Done
The LED on the paired room sensor will flash so you can easily confirm which sensor is connected to that thermostat.
Verify in the Monaire App that the room sensor status shows active (green dot beside it).
Ensure you reinstall this sensor back on the wall to resume accurate room temperature monitoring.

Replacing an Old or Defective Room Sensor

If you are installing a replacement sensor, follow these steps to remove the old device and connect the new one:

  1. Verify Compatibility: Ensure the thermostat and the new sensor series numbers are compatible (reference the compatibility check in Step 2).
  2. Open Settings on the Monaire thermostat: Tap on the three stacked lines (hamburger menu icon).
  3. Scroll down to Management: Select 'Devices & Sensors'.
  4. Select 'Indoor Air Sensor': Tap on the sensor you want to replace.
  5. Delete the Sensor: Select Options > Delete > Delete Sensor.
  6. Pair the New Sensor: Follow the pairing instructions in Step 2 above to add your new sensor.
  7. Confirm Setup: Reference Step 4 above to confirm the new sensor is visible in the Monaire App and set up properly.
5

 Still Having Trouble? Call Monaire Customer Support (339) 666-2473

If you completed the steps above and the sensor remains offline, call Monaire Support at (339) 666-2473. Inform the representative that the troubleshooting steps were attempted.